OBJ Reader - OBJ Options Tab - Revision history

JavaJones at 22:55, 3 June 2012

2012-06-03T22:55:56Z

Jo at 06:30, 16 May 2012

2012-05-16T06:30:05Z

Jo at 06:29, 16 May 2012

2012-05-16T06:29:32Z

Jo at 06:28, 16 May 2012

2012-05-16T06:28:19Z

JavaJones at 02:45, 18 May 2011

2011-05-18T02:45:17Z

127.0.0.1: jrfconvert import

2010-07-11T02:55:39Z

jrfconvert import

New page

[[Category:IMPORT]]
='''OBJ Reader - OBJ Options Tab'''=

[[Image:drex_module_9_3_image_0.png|465pxpx|OBJ Reader - OBJ Options Tab]]

Back to: [[OBJ Reader]]
__NOTOC__

← Older revision		Revision as of 22:55, 3 June 2012
Line 16:		Line 16:

	Back to: [[OBJ Reader]]		Back to: [[OBJ Reader]]
−
−	~~[[Category: Object Nodes]]~~

@@ Line 8: / Line 8: @@
 <ul>
 <li>
-'''Source in cm:''' If this is checked then TG2 interprets the measurement units in the OBJ file as being in centimetres. That's the theory, but there is currently a bug which means the units are interpreted as 10cm (decimetre) rather than 1cm. You may still need to scale the object using the [[OBJ_Reader_-_Transform_Tab|Transform tab]] to make it the correct size.
+'''Source in cm:''' If this is checked then TG2 interprets the measurement units in the OBJ file as being in centimetres. That's the theory, but there is currently a bug which means the units are interpreted as 10cm (decimetre) rather than 1cm. You may still need to scale the object using the [[OBJ_Reader|Transform tab]] to make it the correct size.
 </li><li>
 '''Source Z up:''' Check this if you know the OBJ file uses Z up as opposed to Y up, which TG2 uses. This will cause the coordinates to be swapped when read from the file to match TG2's coordinate system. If the model seems to be laying over on its side when imported you probably need to check this setting.

@@ Line 10: / Line 10: @@
 '''Source in cm:''' If this is checked then TG2 interprets the measurement units in the OBJ file as being in centimetres. That's the theory, but there is currently a bug which means the units are interpreted as 10cm (decimetre) rather than 1cm. You may still need to scale the object using the [[OBJ_Reader_-_Transform_Tab|Transform tab]] to make it the correct size.
 </li><li>
-'''Source Z up:''' Check this if you know the OBJ file uses Z up as opposed to Y up which TG2 uses. This will cause the coordinates to be swapped when read from the file to match TG2's coordinate system.
+'''Source Z up:''' Check this if you know the OBJ file uses Z up as opposed to Y up, which TG2 uses. This will cause the coordinates to be swapped when read from the file to match TG2's coordinate system. If the model seems to be laying over on its side when imported you probably need to check this setting.
 </li>
 </ul>

@@ Line 1: / Line 1: @@
-[[Image:drex_module_9_3_image_0.png|465pxpx|OBJ Reader - OBJ Options Tab]]
+[[Image:drex_module_9_3_image_0.png|center|OBJ Reader - OBJ Options Tab]]
 Back to: [[OBJ Reader]]
-<!-- imported from file: module_9_3.html-->
+[[Category: Object Nodes]]